Delay Timer 77-77

Availability: In stock

$50.00
OR

Quick Overview

Delay Timer 77-77 • This is a replacement timer only, your car will have the existing wiring for this to plug in if you already have this option. If you don't have this option on your car, do not purchase this item, you won't have the wiring in your car.


See Detailed instructions below or go to our tech site at this link.  1977 Delay Timer Replacement Board Installation Instructions.

Details

Delay Timer 77-77 •

1977 Delay Timer Installation Instructions.

First, I thank for the interest in our product.

Facts about the original 1977 Delay Timer

Extensive research has determined that the original 1977 delay timer charged a capacitor inside the module.  This meant the delay light time was different than the later 1978-1982 and 1984-1989 cars.  The amount of time the timer stayed on was determined by how long you had the door open (to a max).  We have tried to get as close to the “mean” to what is/should be considered an acceptable delay.

Another unusual factor with the 77 delay timer was that unlike the 1978 and later cars, when you turned on the ignition switch key the lamp did not turn off.  The cars built after 1977 with delay timers would turn off the interior lamps when you turned the ignition key on.  1977 cars depended on the capacitor bleeding off regardless of whether the key was turned on or not to turn out the lamps. The amount of delay was determined by how long the doors were open and how long the capacitor was charged.

Unfortunately, to replace the timer you are required to remove the left hand dash pad.  You’ll find instructions on how to do this the easiest way possible at this link:  1968-1977 Left Hand Dash Pad Removal, the easiest way. 

This product is only designed for cars that already have the delay timer option ZX2, and out of the 49,213 cars produced in 1977,  40,872 of them came with this option.  If you do not have this option, do not purchase this item.  While all cars had a jump connector (male and female) right on top of the main dash harness, this kit doesn’t come with the jumper harness to install it on a car without this option.  Should you decide to add this option to a car you'll need to contact sales for the appropriate part number for the original jumper harness.  If you don't have this option in the car you simply unplug the wires behind the dash, and then install the jumper harness, then run your ground and your set.  As stated above this module is only made for cars that already have this option. 

The original timer was a metal can design, and when purchased over the counter, it came with the jumper harness to add this option to any car.  Our timer won’t come with this jumper harness, and this is why we say this is only for a car with the existing ZX2 option.

Installation:

The original metal can had a ground wire attached to it, and this ground went to the A pillar as shown in the picture below. You'll have to cut this black wire and splce it together with a butt connector.  You then plugged the timer into the timer connector, tape it to the dash main harness behind the dash pad, and you were set.  On our board, all the electronic components are shrink wrapped in a thick vinyl and loaded on the top side so there will not be any wearing against the main dash harness.  When installing our timer, you’ll need to butt connect (or solder) the timer ground wire to the existing ground and then plug it into the original connector.  It’s that simple. As with all our electronic products, this timer is fused.  If there is any issue with the car the fuse will blow but keep in mind that it can be fixed for a 14.00 charge plus shipping.  Any timer returned to us with a blown fuse will be subject to his repair charge, but this is cheaper than buying another board. 

Also Note: The orange wire shown in the picture below will already be in the car if you have the original timer option.  The original jumper connection will already be bypassed if your car came with the timer option…all you need is the new module and to splice the ground.

Willcox

 

Additional Information

Part Year 1977
Corvette Part Number 975062
WC Part Number 461294
OEM Part Number 461294, 10132879
AIM Part Number 461294
Alt Number No
Class No